Burlap, Felt, and Fleece, OH MY!

Can you guess by the title of this blog post what I have been up to all week?

 Wreath making!!!

 I started with a yarn wreath with fleece flowers...

 Added some OSU letters for all the Buckeye nuts around here...

Then I moved onto burlap... 

And more burlap...

And the weeks not over yet!!!

(Yes, the hot glue love affair continues.)

Coffee Coffee Coffee

I am VERY excited to FINALLY get around to build a coffee table for our living room. In December we bought a new sectional sofa and just went the easy route and used an old chest as a coffee table Now don't get me wrong, I LOVE this chest. It was so much meaning to me; it was my mother's Hope Chest and it somehow made its way into my home. But it was a little too tall and the top surface was not great for cups and feet. So today, I built one!

The "standard" coffee table height is around 18" OR 1"-2" lower than the height of your sofa. We must have a short sofa. I went with a table height of 15" knowing that our current 17" was not comfortable. Other things to consider when determining the size of a coffee table; length and width of a coffee table should be about two-thirds the length of the sofa, and make sure to leave at least 16" from the edge of the sofa.

After determining a rough size idea I went to my lumber stash. I had fully intended to use 2x3 pine for the top because I think it is all tiny yet beefy and precious (I am crazy about wood I tell ya). But as soon as I looked for the other materials I would need I right away changed my plans. I found three pieces of wood leftover from the disassembly of my mom's antique dining table. The size was a bit larger than I had in mind but using these pieces would make it easier, faster, way cheaper, and much more meaningful.

For the base of my table I used 2x3 legs cut with a slight angle. It is really simple to do a tapered leg like these. I just mark and cut one then use that first leg as the template for the rest. Once they are all cut I clamp them together and sand them to make sure they are all even to one another.

Once all pieces were  cut and sanded (legs, side and end aprons) I set up my Kreg Jig and marked and drilled all my pocket holes. On small pieces like this I really like to set up the whole piece as much as possible and mark out everywhere I need a screw. It really helps to save headaches later on (I tend to forget pocket holes for side aprons).

Isn't this beautiful?! Look at all the character!

After that I assembled the base, joined the top boards together, and attached the base to the top. Easy peasy.  But now that I have it in my space I have no ideas on how to finish it!

The old mahogany has really thrown me. I have a hard time matching red tones. Do I paint or stain the base?

I shouldn't touch the top, right? Other than to put on a fresh poly of course. And I really love the old holes in the sides. 

UPDATE: I decided to finish this by staining the base in a mahogany gel stain that is a close match to the top. After that I applied several coats of white wash. Then I buffed with 0000 steel wool and applied a spray protective finish to the entire project.



Crazy Kitchen: Part Two (ceiling details)

So on we went with putting the panels on the ceiling (with the help of two wonderful jack-y things we purchased at Harbor Freight. Let me tell anyone who might think of doing this. It's hard and no fun and even harder if you are a perfectionist (who me, perfectionist??)!  Start by marking out your ceiling joists with a chalk line. We used only screws to attach but I would use glue and screws if I were to do it again to help prevent waves). Starting in one corner work your way to the other side while having a helper push out as much waviness as possible. The sides seams, on the beads, are fairly easy to match and look almost seamless if you take your time. But the butt joints, where ends meet, are impossible to make look good.

Side note; at some point in time, after taking out this weird dumb soffit, my husband insisted that we take out this other section of weird dumb soffit. It REALLY opened up the space but was very messy!

Once you have all your panels up you can fill screw holes and work on your seams (you probably want to countersink your screws and may need to use a countersink bit for this). We used spackle and it took a few coats (and is still not perfect but who cares? My perfectionism only lasted so long.). The screws holes are pretty easy and self explanatory; fill em, that's it. For the bead seams I stuffed some spackle in the seams and smoothed with my finger til it looked good. Pretty easy. Let it all dry and sand carefully (don't want to scratch your panels too much). Repeat as necessary.

Here we are after the first round of filling. You can also see that the joint on the beam has been planed, sanded, and filled.



The Beam: Fairly straightforward to do. This Ana link can help a lot. Ours is similar.

Then onto the trim boards. We first attached 1x3's along the entire perimeter. Then we used a 1x4 down the big ugly butt joint seam. Then placed another one equidistance on the other side. Then we filled those screw holes and it was time to paint!

Here is my sweet husband working hard on trim.

I chose to use a semi-gloss. I know I know. Semi gloss on the ceiling?! God Forbid! But it was what I wanted. I didn't want to have this beautiful but dull ceiling. And I am very happy with it. I used the off the shelf white Valspar from Lowes. It is worth the extra cost over the cheap-o stuff (trust me, I found out the hard and $$ way).

I could not be happier with this ceiling. It makes such a change and a big statement. Love it! We will be doing the same in our laundry room!

More from the Crazy Kitchen Series:

Crazy Kitchen: Part One

Crazy Kitchen: Part Three: The Power of Paint

Crazy Kitchen: Part One

Things I've learned.... blogging is really hard when you have three kids of your own plus one other that you babysit. When I do find time to sit down at my computer there is usually a child on my leg or toys piled in my lap and I am thinking about the fact that I have laundry that needs to be taken out of the washer. But for now I am just blogging for fun and to keep track of my little projects and home milestones, so no pressure.

Do you want to see a few pictures of our most recent home milestone? Meet the ceiling of "Crazy Kitchen". Labor-of-love! **Warning, forgive the variety of awfully lit pictures in all Crazy Kitchen posts. Thanks!**

 Two weekends before I had back surgery, way back in February, we I had this spur of the moment "Hey lets change our ceilings throughout half the house" moment. I had seen bead board ceilings all around internet land and without much research we headed out to the store and bought a ton of bead board panels to install the weekend before my surgery.

Then I researched. First thing I learned and realized once I actually thought about it... it was going to be H.A.R.D to get these panels on the ceiling! And the second thing I learned was that bead board panels are not even close to being fire retardant. So that put a halt to my plans because we intended to run the bead board throughout the entire kitchen and dining area plus the adjoining hallway. The dining area has a wood burning stove which meant no way was I putting bead board panels on my ceiling!

So plans changed and I researched scraping the popcorn (barf) off of the ceilings. We did a test spot and thought it should be pretty easy and planned to get to work ASAP.

Before icky-ness:

And after an HOUR of hard sweaty work:

We had gotten almost no where :(. Square one... what do we do??? Have an aha moment of course! We used this one big room like two rooms anyway, so why not make it more like two rooms? We could install a faux beam and divide off the kitchen area and still use the bead board panels to cover the giant mess we had just made!

We ended up installing the panels, a faux beam, and then trimming it all out to hide the seams and edges.

I will do a full detailed instruction in another post because it is going to be wordy. So stay tuned for that! If you have any questions in the mean time feel free to ask! And I hope you all have a happy and SAFE 4th of July Holiday!



More From the Crazy Kitchen Series

Crazy Kitchen: Part Two (ceiling details)
Crazy Kitchen: Part Three: The Power of Paint



Goals

Hey guys! Boy have I been busy! We had a birthday, a yard sale, two sick kids, and now two weeks of summer kid activities. Plus my husband and I have been doing A LOT of thinking. Thinking about moving... AGAIN! Our friends could tell you that we are movers. We move a lot! And our current home is the longest we have ever lived anywhere, a whopping 3 years! I've been scratching the new house itch for a while now and this week we came really close to jumping into listing our home. But, we stopped. We are going to give ourselves one more year to finish up projects like painting, carpeting, outdoor spaces, and cute-ing up our fugly garage (think 1970 paneling, gag!).

So, while all those things are cosmetics, this girl is thinking of ways to make my house more appealing to a buyer. And it starts with making it appear larger! Our house is only 1400 square feet. It works okay for us but I want to REALLY make sure it works for buyers. So after I finally finish painting my kitchen (which we started a minor cosmetic upgrade to 4 whole months ago!) I will be building a new dining room table that better suits that space. It needs to be much more narrow than my current oval shaped table.  Here are my inspiration photo's.

Take a look at this beauty from William-Sonoma. I drool EVERYTIME I look at it!

And these Restoration Hardware legs are pretty nice!!!

But check out these table tops!!!

Via http://antiquewoodworks.com/trestle-table-farm-32-92--0006.shtml

Via Restoration Hardware

And once the table is all finished, I am really going to have to build this with the plans from Ana White.

I think I want mine to be taller though, like the one in the background of this photo.




Via Country Living

 

What do you guys think? Do you have any other inspiration photo's you'd like to share? Please do!! Look for more on this in about a month... after I finally get around to painting my kitchen. A new table sure is enough to get me inspired!

Holy Table... part 2

Happy Friday everyone! I finally remembered to take my camera to my mom's house and was able to get some decent photos of her Farmhouse Table in action. So to end the week, I'll share my version of Ana White's Farmhouse Table.

 Here is all of the lumber materials needed. Doesn't look like a table, does it? We splurged and got the turned legs and we are so happy we did!

The first thing I did was lay out what would become the top of the table. I cut my breadboard ends, marked and drilled pocket holes, and glued and screwed it all together.

The next part of constructing this table is to build the frame. This was simple for me because I kept the full8 foot length of the side aprons  and just had to cut both end aprons based upon the final width of the top minus the width of two legs. Here's the pieces cut with pocket holes predrilled. Doesn't look like a table frame does it?

Time for the legs! We laid the end apron on a spacer board then attached it nice and square to the legs.

Next we used the same spacer boards to raise up the side aprons and attached them to the legs. And a frame was born! I added 1x2 pieces about every 12 inches in order to screw up through to attach the top.

Now we laid the top face down and center the frame on it and screwed it on! It's that easy! As you can see, this table is about half the size of my whole kitchen!

On to the finish work. Sand until your arms seem like they might come off! I think I did 120, 150, 220 grit. Whew, more than an hour on that! Then I distressed it lightly and sanded it lightly again. Once it is all sanded and whipped clean it was time for stain. I used a mahogany gel stain from Minwax. I applied 3 coats, which was a challenge because I was working in my cold garage. So this is where it became time consuming!



After applying one coat of poly I decided it was too cold (heaters just could not keep up) so we waited a few days for that coat to dry and moved it to my parents house where I put on one more coat of poly. Over the next few days my Dad so kindly put on 3 more coats. After a few days cure time she was ready to use!

Here is the first coat of poly.

And here it is after a total of 5 coats of poly!

Things I would change if/when I do a table of this size again:
1) I would never make a bread board end so large again. I would stick to a 1x6 or smaller. With such a large size we worry about children putting too much pressure on the ends. But so far so good!
2) I will make the legs removable. It was a bear trying to get this table into the house. Thankfully the width was just narrow enough!
3) I won't tackle this in the winter months! Construction of the table took only a few hours but finishing in freezing temps took weeks waiting for warm-ish temperatures

I can't wait for the next one! This table was by far my favorite build to date!